Skip to main content
Bloodlines and dialyzer circuit on a haemodialysis machine

Red end up or blue end up? What the manuals say about dialyzer orientation

In short: which end of the dialyzer faces up does not change clearance in a clinically significant way, because pumps, not gravity, drive blood and dialysate. Orientation matters for air: with the blue (venous) end up, blood flows upward and carries microbubbles out to the venous air trap. What does change clearance is connecting the lines for countercurrent flow; co-current flow gives about 20% less small-molecule clearance. Your dialyzer's instructions for use (IFU) are the document that governs orientation.

Kenya's nephrology nursing community recently debated a question that deserves a documented answer: does it matter which end of the dialyzer faces up during treatment, the red (arterial) end or the blue (venous) end? And does orientation affect how well dialysis clears toxins from the blood? It is a good clinical question, so we went looking for what the documentation says.

The clinical question

Every dialyzer has two ends: the arterial port (red), where blood enters, and the venous port (blue), where blood leaves. When the dialyzer is mounted on the machine, one end points up. The debate is whether this matters, either for clearance during the session or at specific moments such as priming or blood return.

Some nurses argue that orientation affects countercurrent flow and therefore toxin removal. Others follow the practice of their senior colleagues without documented backing. Experienced clinicians have good instincts, and instincts deserve documentation.

What the debate got right

The nurses who raised the countercurrent argument were right that it matters. Countercurrent flow, with blood and dialysate travelling in opposite directions, is not a minor detail.

The literature is clear: co-current flow (both fluids moving in the same direction) results in approximately 20% less diffusive clearance of small molecules such as urea and creatinine [1]. The nurses who insisted that connection orientation matters are correct. And the senior clinicians who said "follow the manufacturer's instructions" are also correct; that instinct needs documentation to back it.

What the manufacturer documentation says

We searched for documentation on the machines most often mentioned in this debate.

Biolight BM-4000

This is the machine that started the conversation, and the one we could not find a public manual for. We searched Biolight's official website (global.blt.com.cn), its product listings and third-party documentation repositories. We found documentation for the D800 series but nothing for the BM-4000.

That gap is worth naming: if this machine is in use in Kenyan public hospitals, the nurses and biomedical engineers operating it should have a clear, readable user manual. We also welcome correction. If you have the Biolight BM-4000 manual and we have something wrong, please send it to us.

Fresenius 5008 CorDiax and 4008S

Both machines have publicly available manuals [2]. We reviewed them and found that neither specifies dialyzer orientation (red end up or blue end up) as an explicit treatment step. This is not unusual. Machine manuals cover how to connect lines to the machine, not how to orient the dialyzer housing itself. That guidance usually lives in the dialyzer's own instructions for use (IFU), the leaflet inside the dialyzer packaging, written by the dialyzer manufacturer [3].

Baxter Artis Physio Plus (formerly Gambro Artis)

The Gambro Artis user manual in our reference library does not contain explicit dialyzer orientation instructions. Baxter's renal division has since been renamed Vantive, and current documentation was hard to access in our search.

The pattern across all three machines is the same: machine manuals focus on circuit connection and set-up, and dialyzer orientation guidance belongs in the dialyzer IFU. Both documents should be in your unit.

What the science says

Here is what the literature supports, and where it is silent.

Does orientation affect clearance?

The evidence says no, not in a clinically significant way. Both blood and dialysate flow are driven by pumps, not gravity. The concentration gradient that drives diffusion is maintained by those pumps whichever end faces up. Kt/V and URR, the standard measures of dialysis adequacy [4], are the same whether the red or the blue end points to the ceiling.

Then why does orientation matter at all?

Because of air. When the blue (venous) end faces up, blood enters at the bottom and travels upward through the hollow fibres. This upward flow helps push microbubbles out through the venous port and into the venous air trap. Microbubbles that stay trapped in the fibres block part of the membrane surface. The effect is too small to show clearly in a single session's clearance figures, but it reduces effective membrane surface over time and raises the risk of clotting in those fibres.

What about gravity and the countercurrent argument?

Gravity does not meaningfully affect diffusive clearance in pump-driven systems. The countercurrent advantage depends on how the lines are connected to the ports, not on which end physically points up. Some theoretical work notes that fluid pressure may be slightly higher at the base of a vertical membrane, but this is not documented as clinically significant in standard haemodialysis practice.

Does orientation change during blood return?

We found no manufacturer guidance recommending a change of dialyzer orientation during blood return. Standard practice keeps the normal treatment position throughout.

Where inversion is used: priming

Some priming protocols briefly invert the dialyzer (arterial end pointing down) during the priming rinse to clear air before treatment begins. After priming, the dialyzer goes back to the venous-end-up position. This is a priming technique, not a treatment orientation. If your unit uses it, it is legitimate; the point is that the dialyzer returns to blue end up before treatment begins.

The practical takeaway

  • Connect for countercurrent flow. Arterial and venous lines on the correct ports. This is the connection with a documented effect of about 20% on clearance.
  • Mount the dialyzer blue (venous) end up during treatment, unless your dialyzer's IFU says otherwise. Upward blood flow helps clear air and protects fibre surface. It does not change your clearance numbers directly, but it protects the dialyzer's effective performance across the session.
  • Read your dialyzer's IFU, the leaflet inside the dialyzer box. That is where your manufacturer's orientation guidance lives, and your unit protocol follows it.
  • Keep the machine manual in the unit. If you do not have it, ask your biomedical engineer or equipment supplier.

Frequently asked questions

Should the red or the blue end of the dialyzer face up?

Blue (venous) end up during treatment, unless the dialyzer's IFU says otherwise. Upward blood flow helps move microbubbles out to the venous air trap.

Does dialyzer orientation affect clearance?

Not in a clinically significant way. Pumps drive both blood and dialysate, so Kt/V and URR are the same with either end up. Line connection matters more: co-current flow gives about 20% less small-molecule clearance than countercurrent flow.

Why is the dialyzer sometimes turned upside down during priming?

Some priming protocols invert it briefly to clear air before treatment. It goes back to blue end up before treatment begins.

Where do I find the manufacturer's guidance on orientation?

In the dialyzer's instructions for use (IFU), the leaflet inside the dialyzer packaging. Machine manuals usually do not cover it.

From Nanto Med

We are equipment suppliers, not clinicians. We supply dialysis machine parts, and when a question like this comes up in Kenya's nephrology community, our role is to go to the documentation and report back, including when documentation is missing.

If your unit runs a Biolight BM-4000 or any other machine without a user manual to hand, tell us the model by WhatsApp or at med@nanto.com, and we will help you find it or the right channel to ask.

This article is produced by Nanto Med for educational purposes. We are equipment suppliers, not clinicians. Nothing here is clinical guidance. Follow your dialyzer's instructions for use and your unit's protocols.

References

  1. Deranged Physiology, Dialyser efficiency and clearance (countercurrent and co-current flow). derangedphysiology.com
  2. Fresenius 5008 service and user manual, via Frank's Hospital Workshop (a free public resource for biomedical engineers). frankshospitalworkshop.com
  3. Fresenius Medical Care, Optiflux dialyzer, product and IFU information. freseniusmedicalcare.com
  4. StatPearls (NCBI Bookshelf), Hemodialysis adequacy, Kt/V and URR. ncbi.nlm.nih.gov/books/NBK544280

Follow us on

Leave a comment